Liquid scintillation efficiencies, gamma-ray emission intensities, and half-life for Gd-153.

Gadolinium-153 was standardized for activity by live-timed anticoincidence counting and an ampoule was submitted to the international reference system (SIR). Absolute emission intensities for the main γ rays were determined with calibrated high-purity germanium (HPGe) and lithium-drifted silicon (Si(Li)) detectors. A revised decay scheme is indicated, with no probability of direct electron capture to the 153Eu ground state. Triple-to-double coincidence ratio (TDCR) efficiency curves indicate that the revised decay scheme is consistent with experiment. Half-life measurements agree with a previous NIST determination and show no sensitivity to chemical environment.

The international reference system for beta-particle emitting radionuclides: Validation through the pilot study CCRI(II)-P1.Co-60.

The Bureau International des Poids et Mesures (BIPM) is developing a new transfer instrument to extend its centralized services for assessing the international equivalence of radioactive standards to new radionuclides. A liquid scintillation counter using the triple/double coincidence ratio method is being studied and tested in the CCRI(II)-P1.Co-60 pilot study. The pilot study, involving 13 participating laboratories with primary calibration capabilities, validated the approach against the original international reference system based on ionization chambers, which has been in operation since 1976. The results are in agreement and an accuracy suitable for purpose, below 5×10-4, is achieved. The pilot study also reveals an issue when impurities emitting low-energy electrons are present in the standard solution, which have a different impact on liquid scintillation counting compared to other primary measurement methods.

Primary standardization of 212Pb activity by liquid scintillation counting.

An activity standard for 212Pb in equilibrium with its progeny was realized, based on triple-to-double coincidence ratio (TDCR) liquid scintillation (LS) counting. A Monte Carlo-based approach to estimating uncertainties due to nuclear decay data (branching ratios, beta endpoint energies, γ-ray energies, and conversion coefficients for 212Pb and 208Tl) led to combined standard uncertainties ≤ 0.20 %. Confirmatory primary measurements were made by LS efficiency tracing with tritium and 4παß(LS)-γ(NaI(Tl)) anticoincidence counting. The standard is discussed in relation to current approaches to 212Pb activity calibration. In particular, potential biases encountered when using inappropriate radionuclide calibrator settings are discussed.

Primary standardization of 224Ra activity by liquid scintillation counting.

A standard for activity of 224Ra in secular equilibrium with its progeny has been developed, based on triple-to-double coincidence ratio (TDCR) liquid scintillation (LS) counting. The standard was confirmed by efficiency tracing and 4παß(LS)-γ(NaI(Tl)) anticoincidence counting, as well as by 4πγ ionization chamber and NaI(Tl) measurements. Secondary standard ionization chambers were calibrated with an expanded uncertainty of 0.62% (k = 2). Calibration settings were also determined for a 5 mL flame-sealed ampoule on several commercial reentrant ionization chambers (dose calibrators).

Preparation and calibration of a 231Pa reference material.

A 231Pa reference material has been characterized for amount of protactinium. This reference material is primarily intended for calibration of 233Pa tracers produced for 235U-231Pa model age measurements associated with nuclear forensics and nuclear safeguards. Primary measurements for characterization were made by isotope dilution mass spectrometry of a purified 231Pa solution using a 233Pa isotopic spike. The spike was calibrated by allowing multiple aliquots of the 233Pa spike solution to decay to 233U and then measuring the ingrown 233U by isotope dilution mass spectrometry using a certified uranium assay and isotopic standard as a reverse-spike. The new 231Pa reference material will simplify calibration of the 233Pa isotope dilution spikes, provide metrological traceability, and potentially reduce the overall measurement uncertainty of model ages.

New determination of the 229Th half-life.

A new determination of the 229Th half-life was made based on measurements of the 229Th massic activity of a high-purity solution for which the 229Th molality had previously been measured. The 229Th massic activity was measured by direct comparison with SRM 4328C using 4παß liquid scintillation counting, NaI counting, and standard addition liquid scintillation counting. The massic activity was confirmed by isotope dilution alpha spectrometry measurements. The calculated 229Th half-life is (7825 ± 87) years (k = 2), which is shorter than the three most recent half-life determinations but is consistent with these values within uncertainties.

Natural Uranium Radioactivity Solution Standard: SRM 4321d.

A new natural uranium solution standard has been produced and will be disseminated by the National Institute of Standards and Technology (NIST) as Standard Reference Material 4321d. The standard is certified for the massic activities of 234U, 235U, and 238U in solution, and it is based on isotopic mass data for the metallic Certified Reference Material (CRM) 112-A (originally issued as SRM 960) that was obtained from THE U.S. Department of Energy, New Brunswick Laboratory. The metallic CRM was chemically cleaned, dissolved, and gravimetrically diluted to prepare a master solution, which was quantitatively dispensed into 5 mL aliquots that were contained within flame-sealed glass ampoules for each SRM unit. Homogeneity among SRM units, verifying solution homogeneity, was substantiated by photonic-emission integral counting with a NaI(Tl) well counter. Confirmatory measurements were performed by liquid scintillation counting for the total massic activity, and by isotope dilution α spectrometry for the 234U and 238U massic activities.

Comparison of (14)C liquid scintillation counting at NIST and NRC Canada.

An informal bilateral comparison of (14)C liquid scintillation (LS) counting at the National Research Council of Canada (NRC) and the National Institute of Standards and Technology (NIST) has been completed. Two solutions, one containing (14)C-labeled sodium benzoate and one containing (14)C-labeled n-hexadecane, were measured at both laboratories. Despite observed LS cocktail instabilities, the two laboratories achieved accord in their standardizations of both solutions. At the conclusion of the comparison, the beta spectrum used for efficiency calculations was identified as inadequate and the data were reanalyzed with different inputs, improving accord.

Standardization of ²³7Np.

The standardization of (237)Np was investigated. The certified massic activity for (237)Np was obtained by 4παß liquid scintillation (LS) counting with correction for the (233)Pa daughter using the CIEMAT/NIST efficiency tracing method using a (3)H standard. Confirmatory measurements were also performed by high-resolution HPGe gamma-ray spectrometry, and by 4παß(LS)-γ(NaI) anticoincidence counting. All results agree within the respective method's uncertainties. It was confirmed that the (237)Np/(233)Pa radioactive equilibrium is disturbed when making dilutions and/or removing aliquots.

Micelle size effect on Fe-55 liquid scintillation efficiency.

We used efficiency tracing techniques to study the micelle size effect on liquid scintillation counting of the electron capture nuclide, (55)Fe. We determined micelle hydrodynamic diameters for specific LS cocktails via dynamic light scattering, and sought trends in efficiencies as a function of micelle size. The presence of Fe(3+) or Mn(2+) ions in the cocktails did not significantly affect micelle sizes or fluorescence quenching. We did not detect any reductions in counting efficiencies due to the micelle size effect.

Measurement of radon and xenon binding to a cryptophane molecular host.

Xenon and radon have many similar properties, a difference being that all 35 isotopes of radon ((195)Rn-(229)Rn) are radioactive. Radon is a pervasive indoor air pollutant believed to cause significant incidence of lung cancer in many geographic regions, yet radon affinity for a discrete molecular species has never been determined. By comparison, the chemistry of xenon has been widely studied and applied in science and technology. Here, both noble gases were found to bind with exceptional affinity to tris-(triazole ethylamine) cryptophane, a previously unsynthesized water-soluble organic host molecule. The cryptophane-xenon association constant, K(a)=42,000 ± 2,000 M(-1) at 293 K, was determined by isothermal titration calorimetry. This value represents the highest measured xenon affinity for a host molecule. The partitioning of radon between air and aqueous cryptophane solutions of varying concentration was determined radiometrically to give the cryptophane-radon association constant K(a)=49,000 ± 12,000 M(-1) at 293 K.

Recent process improvements for the ammonia fiber expansion (AFEX) process and resulting reductions in minimum ethanol selling price.

The ammonia fiber expansion (AFEX) process has been shown to be an effective pretreatment for lignocellulosic biomass. Technological advances in AFEX have been made since previous cost estimates were developed for this process. Recent research has enabled lower overall ammonia requirements, reduced ammonia concentrations, and reduced enzyme loadings while still maintaining high conversions of glucan and xylan to monomeric sugars. A new ammonia recovery approach has also been developed. Capital and operating costs for the AFEX process, as part of an overall biorefining system producing fuel ethanol from biomass have been developed based on these new research results. These new cost estimates are presented and compared to previous estimates. Two biological processing options within the overall biorefinery are also compared, namely consolidated bioprocessing (CBP) and enzymatic hydrolysis followed by fermentation. Using updated parameters and ammonia recovery configurations, the cost of ethanol production utilizing AFEX is calculated. These calculations indicate that the minimum ethanol selling price (MESP) has been reduced from $1.41/gal to $0.81/gal.

A liquid-scintillation-based primary standardization of 210Pb.

A new radioactivity solution standard of 210Pb has been developed and will be disseminated by the National Institute of Standards and Technology (NIST) as standard reference material (SRM) 4337. This new 210Pb solution standard is contained in a 5 mL flame-sealed borosilicate glass ampoule, consists of (5.133+/-0.002)g of a nominal 1mol L(-1) nitric acid solution, has a density of (1.028+/-0.002)g mL(-1) at 20 degrees C, has carrier ion concentrations of about 11 microg Pb2+ and 21 microg Bi3+ per gram of solution, and is certified to contain a massic activity (9.037+/-0.22)kBq g(-1) as of the reference time 1200 EST, 15 June 2006. All of the uncertainties cited above correspond to standard uncertainties multiplied by a coverage factor k=2. The standardization for the (210)Pb content of the solution was based on 4pialphabeta liquid scintillation (LS) measurements using CIEMAT/NIST (3)H-standard efficiency tracing (CNET). Confirmatory determinations were also performed by high-resolution HPGe gamma-ray spectrometry, by 2pialpha spectrometry with a Si surface barrier detector of separated 210Po, and by 4pibeta(LS)-gamma(NaI) anticoincidence counting.

A note on the half-life of 209Po.

The widely adopted value of (102+/-5)a for the (209)Po half-life, which is based on a single determination reported in 1956, appears to be in error by a large factor. Decay data from two separate primary standardizations of a (209)Po solution standard, conducted approximately 12 years apart, are inconsistent with the adopted value and its assigned uncertainty. An estimated half-life, larger than the adopted value by about 25%, is more consistent with the standardization data. A longer half-life is also supported by measurements on a recently standardized (210)Pb solution standard.

Statistical correlation of spectroscopic analysis and enzymatic hydrolysis of poplar samples.

Spectroscopic characterization of poplar wood samples with different crystallinity indices, lignin contents, and acetyl contents was performed to determine changes in the biomass spectra and the effects of these changes on the hydrolysis yield. The spectroscopic methods used were X-ray diffraction for determining cellulose crystallinity (CrI), diffuse reflectance infrared (DRIFT) for changes in C-C and C-O bonds, and fluorescence to determine lignin content. Raman spectroscopy was also used to determine its effectiveness in the determination of crystallinity and C-C and C-O bond changes in the biomass as a complement to better-known methods. Changes in spectral characteristics and crystallinity were statistically correlated with enzymatic hydrolysis results to identify and better understand the fundamental features of biomass that influence enzymatic conversion to monomeric sugars. In addition, the different spectroscopic methods were evaluated separately to determine the minimum amount of spectroscopic data needed to obtain accurate predictions. The principal component regression (PCR) model with only the DRIFT data gives the best correlation and prediction for both initial rate of hydrolysis and also the 72-h hydrolysis yield. The factor that most affects both the initial rate and the 72-h conversion is the O-H bond content of the sample, which directly relates to the breakage of structural carbohydrates into smaller molecules.

Understanding factors that limit enzymatic hydrolysis of biomass: characterization of pretreated corn stover.

Spectroscopic characterization of both untreated and treated material is being performed in order to determine changes in the biomass and the effects of pretreatment on crystallinity, lignin content, selected chemical bonds, and depolymerization of hemicellulose and lignin. The methods used are X-ray diffraction for determination of cellulose crystallinity (CrI); diffusive reflectance infrared (DRIFT) for changes in C-C and C-O bonds; and fluorescence to determine lignin content. Changes in spectral characteristics and crystallinity are statistically correlated with enzymatic hydrolysis results to identify and better understand the fundamental features of biomass that govern its enzymatic conversion to monomeric sugars. Models of the hydrolysis initial rate and 72 h extent of conversion were developed and evaluated. Results show that the hydrolysis initial rate is most influenced by the cellulose crystallinity, while lignin content most influences the extent of hydrolysis at 72 h. However, it should be noted that in this study only crystallinity, lignin, and selected chemical bonds were used as inputs to the models. The incorporation of additional parameters that affect the hydrolysis, like pore volume and size and surface area accessibility, would improve the predictive capability of the models.

Effects of ammonia fiber explosion treatment on activity of endoglucanase from Acidothermus cellulolyticus in transgenic plant.

A critical parameter affecting the economic feasibility of lignocellulosic bioconversion is the production of inexpensive and highly active cellulase enzymes in bulk quantity. A promising approach to reduce enzyme costs is to genetically transform plants with the genes of these enzymes, thereby producing the desired cellulases in the plants themselves. Extraction and recovery of active proteins or release of active cellulase from the plants during bioconversion could have a significant positive impact on overall lignocellulose conversion economics. The effects of ammonia fiber explosion (AFEX) pretreatment variables (treatment temperature, moisture content, and ammonia loading) on the activity of plant-produced heterologous cellulase enzyme were individually investigated via heat treatment or ammonia treatment. Finally, we studied the effects of all these variables in concert through the AFEX process. The plant materials included transgenic tobacco plants expressing E1 (endoglucanase from Acidothermus cellulolyticus). The E1 activity was measured in untreated and AFEX-treated tobacco leaves to investigate the effects of the treatment on the activity of this enzyme. The maximum observed activity retention in AFEX-treated transgenic tobacco samples compared with untreated samples was approx 35% (at 60 degrees C, 0.5:1 ammonia loading, and 40% moisture). Based on these findings, it is our opinion that AFEX pretreatment is not a suitable option for releasing cellulase enzyme from transgenic plants.

Ammonia fiber explosion treatment of corn stover.

Optimizing process conditions and parameters such as ammonia loading, moisture content of biomass, temperature, and residence time is necessary for maximum effectiveness of the ammonia fiber explosion process. Approximate optimal pretreatment conditions for corn stover were found to be temperature of 90 degrees C, ammonia:dry corn stover mass ratio of 1:1, moisture content of corn stover of 60% (dry weight basis), and residence time (holding at target temperature), of 5 min. Approximately 98% of the theoretical glucose yield was obtained during enzymatic hydrolysis of the optimal treated corn stover using 60 filter paper units (FPU) of cellulase enzyme/g of glucan (equal to 22 FPU/g of dry corn stover). The ethanol yield from this sample was increased up to 2.2 times over that of untreated sample. Lowering enzyme loading to 15 and 7.5 FPU/g of glucan did not significantly affect the glucose yield compared with 60 FPU, and any differences between effects at different enzyme levels decreased as the treatment temperature increased.